Skip to main content

TYPES OF NETWORKS

Organizations of different sizes, structures, and budgets need different types of networks. A local newspaper company has needs for its network that would be different from the needs of a multinational company. Networks can be divided into one of two categories: peer-to-peer or server-based networks.

 PEER-TO-PEER NETWORK:
A peer-to-peer network has no dedicated servers; instead, a number of workstations are connected together for the purpose of sharing information or devices. When there is no dedicated server, all workstations are considered equal; any one of them can participate as the client or the server. Peer-to-peer networks are designed to satisfy the networking needs of home networks or of small companies that do not want to spend a lot of money on a dedicated server but still want to have the capability to share information or devices. For example, a small accounting firm with three employees that needs to access customer data from any of the three systems or print to one printer from any of the three systems may not want to spend a lot of money on a dedicated server. A small peer-to-peer network will allow these three computers to share the printer and the customer information with one another. The extra cost of a server was not incurred because the existing client systems were networked together to create the peer-to-peer network. The Microsoft term for a peer-to-peer network is a workgroup. Be aware that peer-to-peer networks typically consist of fewer than 10 systems. Most of the modern operating systems such as Windows XP and Windows Vista already have built-in peer-to-peer networking capabilities, which is why building a peer-to-peer network would be a “cheap” network solution. The disadvantage of a peer-to-peer network is the lack of centralized administration—with peer-to-peer networks, you need to build user accounts and configure security on each system.
Figure: Peer-To-Peer Network
It is important to note that peer-to-peer networks are designed for fewer than 10 systems, and with Microsoft client operating systems such as Windows XP Professional, only 10 concurrent network connections to those clients are allowed. This means that if you have 15 or 20 employees, you eventually will need to implement a server-based network.
SERVER-BASED NETWORKS:
A big disadvantage of peer-to-peer networking is that you can’t do your day-today administration in a single place. With peer-to-peer networking, user accounts typically are created on all the systems, and data files are stored throughout all the systems. This leads to a more complicated environment and makes your job harder as a network administrator. Usually after four or five systems have been networked, the need for a dedicated server to store all of the user accounts and data files becomes apparent this is a server-based network.
The advantage of a server-based network is that the data files that will be used by all of the users are stored on the one server. This will help you by giving you a central point to set up permissions on the data files, and it will give you a central point from which to back up all of the data in case data loss should occur. With a server-based network, the network server stores a list of users who may use network resources and usually holds the resources as well.
Figure: Server-Based-Network
The server in a server-based network may provide a number of different services. The services it will offer to the network usually are decided by the server’s role.
There are a number of different roles that a server could play on a network:
  • File and print servers 
  • Application servers 
  • Web servers 
  • Directory servers 
File and print servers control and share printers and files among clients on the network. File and print servers were the original reason to have a network; a large number of users needed access to the same files, so the files were placed on a server, and all clients were connected to the server when they needed to work with the files.

File servers often have the following characteristics:
  • Large amounts of memory 
  • Fast hard disks 
  • Multiple CPUs 
  • Fast I/O buses 
  • High-capacity tape drives 
  • Fast network adapters 
  • Redundant power supplies 
  • Hot-swappable hard disks and power supplies 
File and print servers also check the access control list (ACL) of each resource before allowing a user to access a file or use a printer. If the user or a group to which the user belongs is not listed in the ACL, the user is not allowed to use the resource, and an “access denied” message appears on the user’s screen. Application servers are servers that run some form of special program on the server. A good example of an application server is a server that runs the company’s e-mail server. The e-mail server software is special software that can be run on a server operating system. Another example of software that would run on an application server is a database server product such as Microsoft SQL Server. A database server is a server that holds the company’s core business data and typically gives this data to custom applications that run on the workstations. These are some applications that you might find on an application server:
  • Microsoft SQL Server 
  • Oracle 
  • Microsoft Exchange Server 
  • IBM Lotus Domino 
Web servers are servers that run the Hypertext Transfer Protocol (HTTP) and are designed to publish information on the Internet or the corporate intranet. Web servers are popular in today’s businesses because they host web applications (web sites) for the organization. These web applications could be designed for internal use, or they could be used to publish information to the rest of the world on the Internet. Examples of web server software are Microsoft’s Internet Information Services that runs on Windows or Apache web server software that runs on UNIX/Linux, Novell NetWare, and Windows. Directory servers hold a list of the user accounts that are allowed to log on to the network. This list of user accounts is stored in a database (known as the directory database) and can store information about these user accounts such as address, city, phone number, and fax number. A directory service is designed to be a central database that can be used to store everything about such objects as users and printers. In a server-based network environment, the centralized administration comes from the fact that the directory server stores all user accounts in its directory database. When a user sits at a client machine to log on to the network, the logon request is sent to this directory server. If the username and password exist in the directory database, the client is allowed to access network resources. It is important to note that a server can have numerous roles at the same time. A server can be a file and print server, as well as an application server, or it can be a file, print, and directory server all at the same time. Because a single server can perform multiple roles, a company will not need to purchase an additional server every time a new product (or feature) is implemented on the network, and this fact reduces the cost of a server-based network.
Labels:

Comments

Post a Comment

Popular posts from this blog

Breaker Schemes in Substations

Breaker Schemes in Substations — Types, Design, Advantages, Disadvantages, and Comparison Author: Engr. Aneel Kumar Figure 1: Infographic overview of breaker schemes commonly used in substations. Introduction The breaker scheme or busbar arrangement in a substation defines how incoming feeders, outgoing feeders, and power transformers are connected to the bus. The choice of scheme has a direct impact on system reliability, maintainability, safety, and cost . A simple bus scheme is economical but vulnerable to outages, while advanced schemes such as breaker-and-a-half or double-bus/double-breaker provide very high reliability but at much higher cost and design complexity. Engineers select breaker schemes considering fault tolerance, maintenance needs, space requirements, expansion possibilities, protection coordination, and capital investment . Below, we explain eac...
Post a Comment
Read more

Advantages of Per Unit System in Power System Analysis | Electrical Engineering

  Advantages of Per Unit System in Power System Analysis In electrical power engineering, the per unit (p.u.) system is one of the most widely used techniques for analyzing and modeling power systems. It is a method of expressing electrical quantities — such as voltage, current, power, and impedance — as fractions of chosen base values rather than their actual numerical magnitudes. This normalization technique provides a universal language for system calculations, minimizing errors, simplifying transformer modeling, and enabling consistency across multiple voltage levels. Because of these benefits, the per unit system is essential in fault analysis, load flow studies, transformer testing, and short-circuit calculations . ⚡ What is the Per Unit System? The per unit system is defined as: Q u a n t i t y ( p u ) = A c t u a l   V a l u e B a s e   V a l u e Quantity_{(pu)} = \dfrac{Actual \ Value}{Base \ Value} Q u an t i t y ( p u ) ​ = B a se   ...
6 comments
Read more

PRIMARY SECONDARY AND TERTIARY FREQUENCY CONTROL IN POWER SYSTEMS

Primary, Secondary and Tertiary Frequency Control in Power Systems Author: Engr. Aneel Kumar Keywords: frequency control, primary frequency control, automatic generation control (AGC), tertiary control, load-frequency control, grid stability. Frequency control keeps the power grid stable by balancing generation and load. When generation and demand drift apart, system frequency moves away from its nominal value (50 or 60 Hz). Grids rely on three hierarchical control layers — Primary , Secondary (AGC), and Tertiary — to arrest frequency deviation, restore the set-point and optimize generation dispatch. Related: Power System Stability — causes & mitigation Overview of primary, secondary and tertiary frequency control in power systems. ⚡ Primary Frequency Control (Droop Control) Primary control is a fast, local response implemented by generator governors (dro...
2 comments
Read more

PRINCIPLE OF OPERATION OF UNIFIED POWER FLOW CONTROLLER UPFC

UPFC consist of two back to back converters named VSC1 and VSC2, are operated from a DC link provided by a dc storage capacitor. These arrangements operate as an ideal ac to ac converter in which the real power can freely flow either in direction between the ac terminals of the two converts and each converter can independently generate or absorb reactive power as its own ac output terminal. Figure: Basic UPFC scheme One VSC is connected to in shunt to the transmission line via a shunt transformer and other one is connected in series through a series transformer. The DC terminal of two VSCs is coupled and this creates a path for active power exchange between the converters. VSC provide the main function of UPFC by injecting a voltage with controllable magnitude and phase angle in series with the line via an injection transformer. This injected voltage act as a synchronous ac voltage source. The transmission line current flows through this voltage source resulting in reactive an...
5 comments
Read more

AC Transmission Line and Reactive Power Compensation: A Detailed Overview

  Introduction The efficient operation of modern power systems depends significantly on the management of AC transmission lines and reactive power. Reactive power compensation is a vital technique for maintaining voltage stability, improving power transfer capability, and reducing system losses. This article explores the principles of AC transmission lines, the need for reactive power compensation, and its benefits in power systems. Keywords: Reactive Power Compensation Benefits, STATCOM vs SVC Efficiency, Power Transmission Stability Solutions, Voltage Stability in Long-Distance Grids, Dynamic Reactive Power Compensation.      Fundamentals of AC Transmission Lines AC transmission lines are the backbone of modern power systems, connecting generation stations to distribution networks. They have distributed electrical parameters such as resistance ( R R R ), inductance ( L L ), capacitance ( C C ), and conductance ( G G ) along their length. These parameters influence ...
Post a Comment
Read more

REVERSING DIRECTION OF ROTATION OF UNIVERSAL MOTOR

The direction of rotation of a universal motor can be changed by either: (i) Reversing the field connection with respect to those of armature; or (ii) By using two field windings wound on the core in opposite directions so that the one connected in series with armature gives clockwise rotation, while the other in series with the armature gives counterclockwise rotation. The second method, i.e, the two field method is used in applications such as motor operated rheostats and servo systems. This method has somewhat simpler connections than the first method. For simple applications like portable drills etc. manual switches are frequently used for reversing the direction of rotation of the motor. Figure  1 (a and b) shows how a DPDT (Double Pole Double Throw) switch and a three position switch may be used for reversing the direction of rotation of single field and double field type of motors respectively. Figure 1 Reversing of a universal motor (a) Armature re...
2 comments
Read more

MAIN AND PILOT EXCITER

Main Exciter The exciter (sometimes called the main exciter) is a synchronous generator that has its stator and rotor windings inverted. Its field winding is fixed in the stator, and the rotor carries the armature or AC . In addition the rotor carries the semiconductor bridge rectifier that converts the armature voltages to a two-wire DC voltage system. The AC voltages and currents in the armature are often alternating at a higher frequency than those in the main generator, e.g. 400 Hz. The higher frequency improves the speed of response of the exciter. The DC power circuit is coupled to the field of the main generator by the use of insulated conductors that pass coaxially inside the rotor of the exciter and the rotor of the main generator. This eliminates the use of slip rings, which were traditionally used before shaft mounted rectifiers were developed. A slight disadvantage of this technique is that the derivative feedback cannot be taken from the output of the exciter. Howeve...
2 comments
Read more