Advantages and Disadvantages of Auto Transformer Starter in Motor Starting

⚡ Introduction

Starting large three-phase induction motors directly on line (DOL) often leads to very high inrush current (6–8 times the full load current). This can cause voltage dips, overheating, and mechanical stress. To overcome this, industries use reduced-voltage starters such as the Auto Transformer Starter, which provides a controlled and smooth motor start.

The auto transformer starter is especially useful in industries with heavy-duty motors (above 15 kW) that require high starting torque but must limit current to avoid disturbing the power supply.

Advantages and Disadvantages of Auto Transformer Starter in Motor Starting — infographic illustration

Infographic: Advantages and Disadvantages of Auto Transformer Starter in Motor Starting

🔧 Working Principle of Auto Transformer Starter

An auto transformer with tap settings (typically 50%, 65%, 80%) is connected between the motor and supply. During starting:

Reduced voltage is applied through the selected tap.
Motor starts with lower current and torque, proportional to tap voltage.
Once the motor reaches near-rated speed, it is switched to full line voltage for normal operation.

This method offers higher starting torque per ampere compared to a Star-Delta Starter.

✅ Advantages of Auto Transformer Starter

Reduced Starting Current
- Limits current to 2–3 times full load current.
- Protects both supply system and motor windings.
Adjustable Voltage Taps
- Multiple taps allow engineers to optimize torque/current ratio.
High Starting Torque
- Provides better torque at reduced current compared to star-delta.
- Suitable for heavy mechanical loads.
Smooth Transition
- Reduces mechanical jerks and prolongs machine life.
Applicable for Large Motors
- Commonly used for motors above 15–20 kW.

❌ Disadvantages of Auto Transformer Starter

High Cost – More expensive compared to star-delta and DOL starters.
Bulky Equipment – Requires more panel space due to the transformer.
Complex Switching – Needs additional contactors and relays for tap selection.
Not Economical for Small Motors – Suitable only for medium-to-large motors.

📌 Applications of Auto Transformer Starter

Heavy-duty compressors and pumps.
Industrial blowers and fans.
Conveyors, crushers, rolling mills.
Any large motor requiring controlled acceleration.

👉 Suggested Read: Flexible AC Transmission System (FACTS)

🔍 Comparison with Star Delta Starter

Feature	Auto Transformer Starter	Star Delta Starter
Starting Current	2–3 × FLC (adjustable)	≈ 1/3 of DOL
Starting Torque	High (adjustable)	Low (~33% of DOL)
Cost	High	Low
Applications	Heavy-duty loads	Medium/light loads

✅ Conclusion

The Auto Transformer Starter is one of the most effective methods for starting large induction motors, offering high starting torque with reduced current. Although it is costlier and bulkier than other starters, its ability to handle heavy-duty applications makes it indispensable in industries.

For smaller motors, Star-Delta Starter may be a cost-effective option, but for large industrial machines, the Auto Transformer Starter remains the preferred choice.

📚 Suggested Read

Comments

PRIMARY SECONDARY AND TERTIARY FREQUENCY CONTROL IN POWER SYSTEMS

Primary, Secondary and Tertiary Frequency Control in Power Systems Author: Engr. Aneel Kumar Keywords: frequency control, primary frequency control, automatic generation control (AGC), tertiary control, load-frequency control, grid stability. Frequency control keeps the power grid stable by balancing generation and load. When generation and demand drift apart, system frequency moves away from its nominal value (50 or 60 Hz). Grids rely on three hierarchical control layers — Primary , Secondary (AGC), and Tertiary — to arrest frequency deviation, restore the set-point and optimize generation dispatch. Related: Power System Stability — causes & mitigation Overview of primary, secondary and tertiary frequency control in power systems. ⚡ Primary Frequency Control (Droop Control) Primary control is a fast, local response implemented by generator governors (dro...

CASCADED TRANSFORMERS METHOD FOR GENERATING AC HIGH VOLTAGE

High-Frequency AC High Voltage Generation Using Cascaded Transformers Author: Engr. Aneel Kumar Figure 1: Infographic representation of cascaded transformers method for generating high AC voltages. Introduction In high voltage engineering , generating very high alternating current (AC) voltages is essential for testing equipment like insulators, circuit breakers, power cables, and other apparatus. One common and effective method for producing such voltages is the cascaded transformers method . This technique uses a series connection of specially designed test transformers , where the secondary of one transformer feeds the primary of the next. In this way, voltages are built up step by step, achieving levels in the range of hundreds of kilovolts (kV) or even megavolts (MV). Working Principle The principle of cascaded connection relies on the fact that each...

ADVANTAGES AND DISADVANTAGES OF CORONA EFFECT IN TRANSMISSION LINES | ELECTRICAL ENGINEERING GUIDE

Advantages and Disadvantages of Corona Effect in Power Systems In high-voltage overhead transmission lines , the corona effect plays a critical role in system performance. Corona occurs when the air around a conductor becomes ionized due to high electric stress. While often seen as a drawback because of power losses and interference , it also provides certain engineering benefits . This article explains the advantages and disadvantages of corona effect in detail, with examples relevant to modern electrical power systems. ✅ Advantages of Corona Effect Increase in Virtual Conductor Diameter Due to corona formation, the surrounding air becomes partially conductive, increasing the virtual diameter of the conductor. This reduces electrostatic stress between conductors and minimizes insulation breakdown risks. Related Reading: Electrostatic Fields in High Voltage Engineering Reduction of Transient Surges Corona acts like a natural cushion for sudden ...

ADVANTAGES OF INTERCONNECTED GRID SYSTEM

Interconnected Grid System: Working, Advantages, Disadvantages, and Comparison with Isolated Grids Author: Engr. Aneel Kumar Figure 1: Infographic showing key advantages of an interconnected grid system. Introduction An interconnected grid system refers to a network of multiple power generation sources, transmission lines, substations, and distribution systems that are linked across regions, states, or even countries. Unlike an isolated grid (or islanded grid) which operates independently, an interconnected grid allows electricity to flow between interconnected nodes, enabling numerous benefits and some trade-offs. In today’s energy landscape—where demand, renewable generation, reliability, and cost pressure are all increasing—understanding how an interconnected grid works, what factors are essential, and what its advantages and disadvantages are is critical for utility planners, reg...

INTERLINE POWER FLOW CONTROLLER IPFC

Recent developments of FACTS research have led to a new device: the Interline Power Flow Controller (IPFC) . This element consists of two (or more) series voltage source converter-based devices (SSSCs) installed in two (or more) lines and connected at their DC terminals. Thus, in addition to serially compensating the reactive power , each SSSC can provide real power to the common DC link from its own line. The IPFC gives them the possibility to solve the problem of controlling different transmission lines at a determined substation . In fact, the under-utilized lines make available a surplus power which can be used by other lines for real power control. This capability makes it possible to equalize both real and reactive power flow between the lines, to transfer power demand from overloaded to underloaded lines, to compensate against resistive line voltage drops and the corresponding reactive line power, and to increase the effectiveness of a compensating system for dynamic disturbanc...

REACTIVE POWER AND ITS SOURCES

REACTIVE POWER: Reactive power is a concept used by engineers to describe the background energy movement in an Alternating Current (AC) system arising from the production of electric and magnetic fields. These fields store energy which changes through each AC cycle. Devices which store energy by virtue of a magnetic field produced by a flow of current are said to absorb reactive power; those which store energy by virtue of electric fields are said to generate reactive power. Power flows, both actual and potential, must be carefully controlled for a power system to operate within acceptable voltage limits. Reactive power flows can give rise to substantial voltage changes across the system, which means that it is necessary to maintain reactive power balances between sources of generation and points of demand on a 'zonal basis'. Unlike system frequency, which is consistent throughout an interconnected system, voltages experienced at points across the system form a "voltage ...

Advantages of Per Unit System in Power System Analysis | Electrical Engineering

Advantages of Per Unit System in Power System Analysis In electrical power engineering, the per unit (p.u.) system is one of the most widely used techniques for analyzing and modeling power systems. It is a method of expressing electrical quantities — such as voltage, current, power, and impedance — as fractions of chosen base values rather than their actual numerical magnitudes. This normalization technique provides a universal language for system calculations, minimizing errors, simplifying transformer modeling, and enabling consistency across multiple voltage levels. Because of these benefits, the per unit system is essential in fault analysis, load flow studies, transformer testing, and short-circuit calculations . ⚡ What is the Per Unit System? The per unit system is defined as: Q u a n t i t y ( p u ) = A c t u a l V a l u e B a s e V a l u e Quantity_{(pu)} = \dfrac{Actual \ Value}{Base \ Value} Q u an t i t y ( p u ) = B a se ...

ENGINEERING ARTICLES

Search This Blog